Mistake one: treating argon as the headline upgrade
It gets top billing in a lot of sales presentations because it is easy to explain and sounds technical. In the real hierarchy of what makes a window perform, it sits well down the list. Each of these moves the result more:
- Whether the installation seals the opening properly.
- The frame material and whether it has a thermal break.
- The low-E coating and which glass surface it lands on.
- The spacer holding the two panes apart.
The tell is the order of the conversation. Someone who has actually installed windows through an Indiana winter opens with the opening, not with the glass, because that is where the callbacks come from. If the gas comes up in the first five minutes and the flashing detail never comes up at all, you are being sold a product rather than a job. A useful reframe: argon is a finishing touch on a good window and a fig leaf on a bad one.
Mistake two: paying a premium for something already included
How the option list gets padded
Some proposals present a base package nobody actually sells, then add back the features that come standard from the factory. Argon is a favorite for this because customers recognize the word and feel informed choosing it. You end up paying a line item for something the manufacturer would have put in either way.
The defense takes one email. Ask for the manufacturer spec sheet for the exact series being quoted and check what the standard glass package includes. Anything already listed there should not reappear as a paid upgrade on your paperwork. Watch for the second version of the same trick too: a quote that includes argon and quietly drops the warm-edge spacer, or steps the coating down a grade to protect the margin. Compare glass packages line by line, not feature by feature.
Mistake six: cutting the installation to afford the glass
Where the heat actually leaves an older Broad Ripple house
The most expensive mistake on this list. A premium insulated unit set into a poorly prepared opening will underperform a modest window installed properly, every single time. In homes built before the mid-1980s the openings often have no insulation between frame and framing at all, just a void or a handful of batt stuffed in during construction.
Proper work means the old frame is dealt with honestly rather than buried, the gap is filled with low-expansion foam, the exterior is flashed and sealed against wind-driven rain, and the interior is air-sealed before trim goes back on. None of that appears in a glass specification, and all of it outweighs what is in the cavity.
What a proper opening actually costs
Doing it right adds time rather than exotic materials. Expect a crew to spend meaningfully longer per window than a tear-out-and-caulk outfit does, and expect that to land in the labor line rather than the product line. When two quotes sit hundreds apart per opening on the same window, the difference is almost always here, and it is the one part of the job you can never inspect once the trim is back on.
Mistake four: assuming a clear window still holds its fill
Signs that arrive before the fog
Fogging is a late-stage symptom. A unit can be most of the way empty and still look flawless. Earlier hints are subtler: one window in a row that consistently sweats first on a cold morning, a faint distortion when you sight across the glass at a shallow angle, or a sash that feels noticeably colder than its neighbor on the same wall at the same hour.
None of those is proof on its own. Any of them is reason enough to have a glass shop check the unit with a gas analyzer before you commit to a whole-house replacement. The cost of guessing runs both directions. Replacing sound units wastes money now. Leaving failed ones wastes it slowly, because a unit with a broken seal has lost most of its insulating value and keeps collecting mineral deposits until the glass is permanently marked.
Mistake five: buying triple pane in Broad Ripple for the wrong reason
Triple glazing gives you two gas-filled cavities instead of one, and in a heating climate like central Indiana it does measurably outperform double. But it costs substantially more, it is heavier, a large operating sash gets harder to lift, and the extra depth can complicate an insert into a shallow original frame.
Buying triple because someone said more argon is better is not the same as buying it because you want a whole-window U-factor near 0.20 and are willing to pay for it. There is a maintenance angle nobody raises at the kitchen table, either: three panes put more weight on the balances of a double-hung, and balances are the most common hardware failure on any operable window. If the real driver is one cold room rather than a whole-house energy target, triple pane in that room only is a sensible compromise almost nobody gets offered.
Mistake seven: never checking the warranty clock on Broad Ripple glass
Insulated units are consumable in a way people do not expect. The seal has a service life, and Indiana's freeze and thaw swings plus humid summers work it hard. If your windows are fifteen or eighteen years old and one has fogged, the rest are on the same clock: same build date, same seal design, same weather.
| Glass build date | Where you probably stand |
|---|---|
| Within the last 10 years | Comfortably inside most seal warranties. A failure is a claim, not a project. |
| 10 to 18 years | Prorated territory. Check the term and the labor clause before replacing anything. |
| More than 18 years | Usually out of warranty. Plan by room or by elevation rather than unit by unit. |
Find the spacer stamp, get the build date, and work out where you sit before you make a plan. Replacing failed units one at a time is sometimes exactly right. Sometimes it is money spent on a set of windows that will all go within five years. If no stamp is legible, closing paperwork from the previous owner or a permit record often pins the year, and failing that the age of the house is a fair fallback, because original windows and original seals share a birthday.
One clause catches people out more than any other. Most glass warranties run to the original purchaser only, which quietly excludes anyone who bought the house after the windows went in. Check that line first if you were not the person who signed the contract, because it can turn a twenty-year warranty into no warranty at all.
Mistake three: expecting the house to get quieter
What actually cuts road noise
People replace windows for noise more often than they admit, and they are routinely told the gas will help. Any effect is far too small to notice from inside the room. Real noise control comes from mass and from breaking up resonance: laminated glass with a plastic interlayer, panes of unequal thickness in the same unit, a wider cavity, and a frame that closes tightly. If a quiet bedroom is the goal in a Broad Ripple house near a busy road, say so out loud and ask specifically about laminated glass on that elevation.
The other half of the noise problem is not glass at all. Sound travels through gaps far more readily than through materials, so an unsealed perimeter or a worn meeting rail undoes an expensive glass package instantly. Close the leaks first, then judge the noise.